<ins id="lfbhb"><thead id="lfbhb"></thead></ins>

                <dl id="lfbhb"></dl>

                發布技術資料
                您現在所在的位置 > 儀表網 儀表技術 > 資料下載

                JYJ-D智能雙顯絕緣電阻測試儀

                關鍵詞:
                絕緣電阻測試儀,絕緣電阻測試儀性能,絕緣電阻測試儀參數,絕緣電阻測試儀規格
                下載次數:
                702
                文檔類型:
                上傳時間:2019-09-29  |  人氣:702
                -------------上傳人-------------

                江蘇久益電力設備有限公司

                進入該公司展臺

                資料簡介

                JYJ-D智能雙顯絕緣電阻測試儀

                 

                一、   產品特性

                1 有兩種電壓輸出選擇2500V/5000V,測量電阻量程范圍可達0200GΩ,電阻量程范圍可自動轉換,并有相應的指示。

                2 兩種方式同步顯示絕緣阻值。機械指針采用超薄型張絲結構抗震能力強。機械指針的采用可容易觀察絕緣電阻的變化范圍,點陣液晶屏的采用可指導用戶操作儀表并可精確得出測量結果。

                3 機械表頭與液晶屏合二為一。雙刻度顯示,量程自動轉換。彩色刻度易于讀識,并有LED顯示相應色彩。

                4 采用嵌入式工業單片機和實時操作軟件系統。自動化程度高、抗干擾能力強,儀器可自動計算吸收比和極化指數,無須人工干預。

                5 操作界面友好,各種測量結果具有防掉電功能,可連續存儲9次的測量結果。

                6 儀表產生高壓時,有提示音輸出。

                7 內置殘留高壓放電電路,測試完畢可自動監視并放掉被測設備上的殘留高壓。

                8 交直流兩用,內置可充電池和智能充電模塊。整機輸出功率大(2500V短路電流>2mA5000V短路電流>2mA)。

                9、儀表采用便攜式設計,便于野外操作。

                10、是測量大型變壓器、互感器、發電機、高壓電動機、電力電容、電力電纜、避雷器等絕緣電阻的理想測試儀器。

                JYJ-D智能雙顯絕緣電阻測試儀

                儀表原理

                 

                1、測試原理

                儀表高壓產生部分采用高頻開關脈沖寬度調制(PWM),由單片機控制調節輸出負極性直流高壓,具有節能,電壓線性度好、穩定、紋波系數小等特點。

                由儀表線路端(LINE)產生的高壓經過負載電阻Rx,流回儀表地端(EARTH)。經內部電路采樣分兩路信號,一路經V/I轉換驅動指針表頭,另一路經A/D轉換,由單片機進行處理,結果由液晶屏顯示。同時單片機處理高壓幅值及電源電壓信號。

                采用工業高速單片機,使得指針與數顯值完全同步。

                電源充電采用智能充電模塊,無須人工調節充電參數。

                 

                 

                準備工作

                注意:當第一次使用儀表時,需充電6小時。否則儀表不能正常

                      工作。充電方法祥見電池充電的相關內容。

                1 試驗前應拆除被試設備電源及一切對外連線,并將被試物短接后接地放電1min,電容量較大的應至少放電2min以免觸電和影響測量結果。

                2 效驗儀表指針是否在無窮大上,否則需調整機械調零螺絲(9)

                3 用干燥清潔的柔軟布擦去被試物的表面污垢,必要時先用汽油洗凈套管的表面積垢,以消除表面漏電電流影響測試結果。

                4、將帶屏蔽高壓測試線一端(紅色)插入(1LINE端,另一端(紅色)接于被試設備的高壓導體上,將帶屏蔽高壓測試線屏蔽端(黑色)插入(2GROUND端,另一端接于被試設備的高壓護環上,以消除表面泄漏電流的影響(祥見屏蔽端的使用方法相關內容。將另外一根黑色測試線插入地端(EARTH)(3)端,另一頭接于被試設備的外殼或地上。以電纜測試為例接法如圖3所示。

                 

                 

                 

                 

                儀表知識庫


                媒體平臺


                儀表站,幫你做
                生意的APP

                微信公眾號新浪微博投稿聯系媒體合作建議反饋


                新手指南
                了解儀表網賣家注冊買家注冊操作指南手機版儀表網
                旗下子站
                流量儀表溫度儀表壓力儀表液位儀表氣體檢測工控儀表
                站點導航
                找資訊找企業找產品找展會找品牌
                本站服務
                會員服務企業建站廣告服務SEO優化興旺通在線投訴

                返回首頁
                關閉
                友情提示:
                如果您已經是儀表網的會員,請先 登錄 后留言,這有助于您便捷留言,更好的和客戶溝通,還不是會員?
                立即 免費注冊
                提交留言
                點擊下載
                [{"ID":"90846","CompanyID":"84282","PgID":"84","Sort":"0","Title":"JYJ-D智能雙顯絕緣電阻測試儀","Picture":"","PictureDomain":"","ClassID":"229","Author":"","FileType":"doc","Language":"","UpdateTime":"2019/9/29 8:10:43","HitNumber":"702","IsVip":"0","Integral":"0","FileName":"1/20190929/637053413575989215792.doc","FileSize":"278016","FileDomain":"img70","Detail":"

                JYJ-D智能雙顯絕緣電阻測試儀<\/strong><\/p>

                 <\/p>

                一、<\/span><\/span><\/span><\/strong>   產品特性<\/span><\/span><\/span><\/strong><\/p>

                1<\/span><\/span><\/span>、<\/span><\/span><\/span> 有兩種電壓輸出選擇<\/span><\/span><\/span>2500V/5000V<\/span><\/span><\/span>,測量電阻量程范圍可達<\/span><\/span><\/span>0<\/span><\/span><\/span>~<\/span><\/span><\/span>200GΩ<\/span><\/span><\/span>,電阻量程范圍可自動轉換,并有相應的指示。<\/span><\/span><\/span><\/p>

                2<\/span><\/span><\/span>、<\/span><\/span><\/span> 兩種方式同步顯示絕緣阻值。機械指針采用超薄型張絲結構抗震能力強。機械指針的采用可容易觀察絕緣電阻的變化范圍,點陣液晶屏的采用可指導用戶操作儀表并可精確得出測量結果。<\/span><\/span><\/span><\/p>

                3<\/span><\/span><\/span>、<\/span><\/span><\/span> 機械表頭與液晶屏合二為一。雙刻度顯示,量程自動轉換。彩色刻度易于讀識,并有<\/span><\/span><\/span>LED<\/span><\/span><\/span>顯示相應色彩。<\/span><\/span><\/span><\/p>

                4<\/span><\/span><\/span>、<\/span><\/span><\/span> 采用嵌入式工業單片機和實時操作軟件系統。自動化程度高、抗干擾能力強,儀器可自動計算吸收比和極化指數,無須人工干預。<\/span><\/span><\/span><\/p>

                5<\/span><\/span><\/span>、<\/span><\/span><\/span> 操作界面友好,各種測量結果具有防掉電功能,可連續存儲<\/span><\/span><\/span>9<\/span><\/span><\/span>次的測量結果。<\/span><\/span><\/span><\/p>

                6<\/span><\/span><\/span>、<\/span><\/span><\/span> 儀表產生高壓時,有提示音輸出。<\/span><\/span><\/span><\/p>

                7<\/span><\/span><\/span>、<\/span><\/span><\/span> 內置殘留高壓放電電路,測試完畢可自動監視并放掉被測設備上的殘留高壓。<\/span><\/span><\/span><\/p>

                8<\/span><\/span><\/span>、<\/span><\/span><\/span> 交直流兩用,內置可充電池和智能充電模塊。整機輸出功率大(<\/span><\/span><\/span>2500V<\/span><\/span><\/span>短路電流<\/span><\/span><\/span>>2mA<\/span><\/span><\/span>、<\/span><\/span><\/span>5000V<\/span><\/span><\/span>短路電流<\/span><\/span><\/span>>2mA<\/span><\/span><\/span>)。<\/span><\/span><\/span><\/p>

                9<\/span><\/span><\/span>、儀表采用便攜式設計,便于野外操作。<\/span><\/span><\/span><\/p>

                10<\/span><\/span><\/span>、是測量大型變壓器、互感器、發電機、高壓電動機、電力電容、電力電纜、避雷器等絕緣電阻的理想測試儀器。<\/span><\/span><\/span><\/p>

                JYJ-D智能雙顯絕緣電阻測試儀<\/strong><\/p>

                儀表原理<\/span><\/span><\/span><\/strong><\/p>

                 <\/p>

                1<\/span><\/span><\/span>、測試原理<\/span><\/span><\/span><\/p>

                儀表高壓產生部分采用高頻開關脈沖寬度調制(<\/span><\/span><\/span>PWM<\/span><\/span><\/span>),由單片機控制調節輸出負極性直流高壓,具有節能,電壓線性度好、穩定、紋波系數小等特點。<\/span><\/span><\/span><\/p>

                由儀表線路端(<\/span><\/span><\/span>LINE<\/span><\/span><\/span>)產生的高壓經過負載電阻<\/span><\/span><\/span>Rx<\/span><\/span><\/span>,流回儀表地端(<\/span><\/span><\/span>EARTH<\/span><\/span><\/span>)。經內部電路采樣分兩路信號,一路經<\/span><\/span><\/span>V/I<\/span><\/span><\/span>轉換驅動指針表頭,另一路經<\/span><\/span><\/span>A/D<\/span><\/span><\/span>轉換,由單片機進行處理,結果由液晶屏顯示。同時單片機處理高壓幅值及電源電壓信號。<\/span><\/span><\/span><\/p>

                采用工業高速單片機,使得指針與數顯值完全同步。<\/span><\/span><\/span><\/p>

                電源充電采用智能充電模塊,無須人工調節充電參數。<\/span><\/span><\/span><\/p>

                 <\/p>

                 <\/p>

                準備工作<\/span><\/span><\/span><\/strong><\/p>

                注意:<\/span><\/span><\/span><\/strong>當第一次使用儀表時,需充電<\/span><\/span><\/span>6<\/span><\/span><\/span>小時。否則儀表不能正常<\/span><\/span><\/span><\/p>

                      工作。充電方法祥見<\/span><\/span><\/span>“<\/span><\/span><\/span>電池充電<\/span><\/span><\/span>”<\/span><\/span><\/span>的相關內容。<\/span><\/span><\/span><\/p>

                1<\/span><\/span><\/span>、<\/span><\/span><\/span> 試驗前應拆除被試設備電源及一切對外連線,并將被試物短接后接地放電<\/span><\/span><\/span>1min<\/span><\/span><\/span>,電容量較大的應至少放電<\/span><\/span><\/span>2min<\/span><\/span><\/span>以免觸電和影響測量結果。<\/span><\/span><\/span><\/p>

                2<\/span><\/span><\/span>、<\/span><\/span><\/span> 效驗儀表指針是否在無窮大上,否則需調整機械調零螺絲<\/span><\/span><\/span>(9)<\/span><\/span><\/span>。<\/span><\/span><\/span><\/p>

                3<\/span><\/span><\/span>、<\/span><\/span><\/span> 用干燥清潔的柔軟布擦去被試物的表面污垢,必要時先用汽油洗凈套管的表面積垢,以消除表面漏電電流影響測試結果。<\/span><\/span><\/span><\/p>

                4<\/span><\/span><\/span>、將帶屏蔽高壓測試線一端(紅色)插入(<\/span><\/span><\/span>1<\/span><\/span><\/span>)<\/span><\/span><\/span>LINE<\/span><\/span><\/span>端,另一端(紅色)接于被試設備的高壓導體上,將帶屏蔽高壓測試線屏蔽端(黑色)插入(<\/span><\/span><\/span>2<\/span><\/span><\/span>)<\/span><\/span><\/span>GROUND<\/span><\/span><\/span>端,另一端接于被試設備的高壓護環上,以消除表面泄漏電流的影響(祥見<\/span><\/span><\/span>“<\/span><\/span><\/span>屏蔽端的使用方法<\/span><\/span><\/span>”<\/span><\/span><\/span>相關內容。將另外一根黑色測試線插入地端(<\/span><\/span><\/span>EARTH<\/span><\/span><\/span>)(<\/span><\/span><\/span>3<\/span><\/span><\/span>)端,另一頭接于被試設備的外殼或地上。以電纜測試為例接法如圖<\/span><\/span><\/span>3<\/span><\/span><\/span>所示。<\/span><\/span><\/span><\/p>

                 <\/p>

                 <\/p>

                 <\/p>

                 <\/p>","DownNumber":"6","IsShow":"10","PositionFlag":"1","Tag":"絕緣電阻測試儀,絕緣電阻測試儀性能,絕緣電阻測試儀參數,絕緣電阻測試儀規格","CreateTime":"2019/9/29 8:10:43","Reprint":"","ProvinceId":"15","CityId":"95","ShowState":"0","Subtitle":"","Summary":"","IssuingAgency":"","CertificateNum":"","BoothShow":"0","BeginTime":"1900/1/1 0:00:00","EndTime":"1900/1/1 0:00:00","HomeTitle":"","DownPassWord":"","ClassName":"資料下載","StandUrl":"/st84282","IsCharges":"1","CompanyName":"江蘇久益電力設備有限公司","PackageName":"中級榜上有名","UserID":"104027","TrueHitNumber":"702","VitualHitNumber":"0","CreateUserID":"0","CreateUserName":"","FeedBackMsg":"","IsDownPower":"0"}]